Pulling Grip

Single Weave, Single Eye, Light Duty (Series 00661)

These grips offer a flexible eye with single weave galvanized wire construction for light duty applications. They are also supplied in a kit with pouch.

Pulling Grip

Non-Conductive, Single/Double Weave, Single Eye (Series 00662 & 00664)

These grips are non-conductive and may be used to install fiber optic cable. Smaller sizes are single weave, larger sizes go to double weave.

Pulling Grip

Double Weave, Single Eye (Series 00670 & 00671)

These grips offer a flexible eye and double weave galvanized wire construction for the regular load pulls. There are three lengths available.

Pulling Grip

Double Weave, Single Eye, Slack Grip, Closed Mesh (Series 00674 & 00675)

These grips offer a flexible eye and double weave galvanized wire construction – for those times when a side loaded pulling rope is easier. If the cable end is available, then the closed mesh is preferred. Available in standard length and long length.

Pulling Grip

Double Weave, Single Eye, Slack Grip, Split Mesh (Series 00678 & 00679)

These grips offer a flexible eye and double weave galvanized wire construction – for those times when a side loaded pulling rope is easier. If the cable end is not available, then the split mesh is preferred.

Pulling Grip

Double Weave, Single Eye, Shoulders (Series 00680)

These grips offer a flexible eye with shoulders and double weave galvanized wire construction. The shoulders offer added protection to the utility being pulled in as well as protecting the leading wire strands.

Pulling Grip

Triple Weave, Single Eye, Shoulders (Series 00681)

These grips offer a flexible eye with shoulders and triple weave galvanized wire construction. The shoulders help to protect the leading edge of the cable or ducting and this type should be used for heavy duty applications.

Pulling Grip

Triple Weave, Single Eye, Rotary Head, Shoulders (Series 00682)

These grips offer a stainless steel rotary head with shoulders and triple weave galvanized wire construction. The shoulders help to protect the leading edge of the cable or ducting and this type should be used for heavy duty applications.

Note: Severe damage may occur to the utility being installed if this product is used without the correct swivel.

Pulling Grip

Double Weave, Rotating Head, Shoulders (Series 00690)

These grips offer a flexible eye with shoulders and double weave galvanized wire construction. The shoulders help to protect the leading edge of the cable or ducting and this type should be used for heavy duty applications.

Note: Severe damage may occur to the utility being installed if this product is used without a proper swivel.

Pulling Grip

Dual Wire, Double Weave, High Strength, Shoulders (Series 00695)

These extra high strength grips feature a dual wire, double woven construction. This type of grip should be used for heavy duty applications such as overhead transmission wire. The grips are particularly suited to bare conductor and synthetic rope applications.

Feed Tube

Feed Tube (Series 00696)

When pulling rope, this feed tube can be used to help feed the leading end of the rope into the grip.

Open Ends Pulling Grip

Double Weave – Open Ends (Series 00697)

These grips are open both ends to butt rope or cable ends together, (ex. for elevator or crane rope replacement), and have a double weave galvanized wire construction. The old cable may be attached to the new one and simply pulled through the blocks.

Single Eye, Single Weave, Closed Mesh (Series 00800)

Support Grip

These grips are for permanent installations, horizontal or vertical, where the cable end is available for assembly of the support grip.

 

Support Grip

Double Eye, Single Weave, Closed Mesh (Series 00801)

Fitted with a double eye, for permanent installations where the cable end is available for assembly of the support grip.

Support Grip

Offset Eye, Single Weave, Closed Mesh (Series 00802)

For permanent installations where the support point is offset and the cable end is available for assembly of the support grip.

Support Grip

Single Eye, Single Weave, Split Mesh, Lace-Up (Series 00810)

For permanent installations where the cable end is not available for assembly of the support grip, the support grip may be laced over the mid-span.

Support Grip

Double Eye, Single Weave, Split Mesh, Lace-Up (Series 00811)

Fitted with a double eye, for permanent installations where the cable end is not available for assembly of the support grip, the support grip may be laced over the mid-span.

Support Grip

Offset Eye, Single Weave, Split Mesh, Lace-Up (Series 00812)

For permanent installations where the support point is offset and the cable end is not available for assembly of the support grip, the support grip may be laced over the mid-span.

Support Grip

Single Eye, Double Weave, Closed Mesh (Series 00820)

For heavy duty permanent installations, horizontal or vertical, where the cable end is available for assembly of the support grip.

Support Grip

Double Eye, Double Weave, Closed Mesh (Series 00821)

Fitted with a double eye, for heavy duty permanent installations where the cable end is available for assembly of the support grip.

Support Grip

Single Eye, Double Weave, Split Mesh – Lace Up (Series 00830)

For heavy duty permanent installations where the cable end is not available for assembly of the support grip, the support grip may be laced over the mid-span.

Support Grip

Dual Eye, Double Weave, Split Mesh – Lace Up (Series 00831)

Fitted with a double eye, for heavy duty permanent installations where the cable end is NOT available for assembly of the support grip, the support grip may be laced over the mid-span.

Wire Grip Swivel

Wire Grip Swivel (Series 00501)

These swivels may be used in conjunction with either the 00670 or 00680 Wire Mesh Grips. They will allow the utility being installed to “unwind” as it is being pulled in, but like the Rotary Heads, these swivels will not rotate under load.

Fiber Headboard

Fiber Headboard (Part No. 00698-035)

The Fiber Headboard is an anti-torsional device for pulling OPGW cable. It incorporates a 00505-035 series swivel at the lead (pulling line) end, a 00520-035 can-link connector at the tail (OPGW cable) end, and three dangling arms providing the torque stability required to prevent turning.

DCD Design and Manufacturing

Place Your Order Now!