Clevis Pins

Clevis Pins (Series 00000)

All clevis pins are manufactured from heat treated 416 Stainless Steel to provide superior strength and wear. Hardness is between 37-40 Rc. The DCD Clevis Pin is a shouldered type of pin rather than a simple straight pin without any head. This design greatly improves the strength of the clevis by not allowing side loads to spread the clevis opening.

Line Swivel

Line Swivel (Series 00505)

DCD Line Swivels are typically constructed with a thrust bearing for tensile load and a radial bearing for bending load. They combine a high safe working load with a compact design. All sizes incorporate an oil seal and are manufactured from high strength stainless steel. Our line swivels are designed for cable pulling or hauling in overhead and underground applications. Always remember to grease your swivel!

Locking Line Swivel

Locking Line Swivel (Series 00505A)

DCD Locking Line Swivels are typically constructed with a bronze thrust bearing for tensile load and a radial bearing for bending load. The bronze bearing will rotate up to a portion of the safe working load before locking. Once past this point, then rotation will only occur when pulling tension is relieved. Always remember to grease your swivel!

Can Link Connector

Can-Link Connectors (Series 00520)

The Can-Link Connectors are used to connect two items with lug or wire loop fittings. A common use is to connect a wire mesh grip to the pulling wire. The connectors are manufactured from high strength stainless steel with hardened clevis pins. The two smaller sizes have slotted clevis pins, while the larger sizes have hexagon clevis pins.

Rope to Rope Connector

Rope to Rope Connectors (Series 00521)

The Rope to Rope Connectors are used to connect two ropes of up to 7/8″ diameter. The entire product, including sheaves, is manufactured from Stainless Steel. Replacement sheaves are available by contacting the customer service department. The sheaves run on standard DCD Clevis pins, which are also available as spares. This product is available only in the one size since it can also easily be used for smaller rope sizes.

Rope to Swivel Connector

Rope to Swivel Connectors (Part No. 00522)

The Rope to Swivel Connector is designed to achieve in two products what the competition does in four. These all Stainless Steel connectors are designed to maximize usefulness by both catering to the same rope capacity and simply offering different ends to attach to the most popular swivel sizes. Replacement sheaves are available by contacting the customer service department.

Duct Puller

Duct Puller (00616)

 

This Duct Puller is nearly identical to the 00619 Series, except for the front face plate. The 00616 puller is made from zinc dichromate coated steel. This puller will also cover a larger range of bore sizes compared to the 00620 series and is made of fewer moving parts so maintenance and repair is easy.

For metric sizes, refer to the 00617 series.

Duct Puller

Duct Puller (00619)

This DCD puller has several features that make it a different puller than the others on the market. Most obvious is the polyurethane nose cone – this material has proved to be extremely durable during field testing. This puller will also cover a larger range of bore sizes compared to the 00620 series and is made of fewer moving parts so maintenance and repair is easy.

Duct Puller

Duct Puller (00620/00621)

 

These products are designed to grip polyethylene ducting using expanding jaws to grip the inside wall of the duct. This causes the pulling load to be spread around the circumference of the duct and allows a maximum load to be applied without damage to the ducting.

For metric sizes, refer to the 00621 series.

Eye to Eye Connector

Eye to Eye Connector (Series 00652 & 00653)

Eye to Eye Connectors are the standard Chain Swivel used in many applications. The two halves will not rotate under load, but are useful for aligning products. They are forged from carbon steel and galvanized for protection. Ultimate load is 5 times Safe Working Load.

Connecting Shackles

Connecting Shackles (Series 00654 & 00655)

DCD shackles provide a low cost, economical means of connecting two products together. Available in two types – one (00654 series) with a bolt, nut and cotter pin for locking, the other (00655 series) with a one piece bolt with a flanged head suitable for wire locking if needed. Ultimate load is 6 times Safe Working Load.

Chain Link Connectors

Chain Link Connectors (Series 00656)

The Chain Link Connectors are useful and easy to insert in any pulling line. They allow easier bending of a Pulling Eye or other rigid component when going around bends or sheaves. These high quality products are manufactured with Grade 80 steel. Safety Factor is 3:1.

Quick Link Connectors

Quick Link Connectors (Series 00660)

The Quick Link Connectors are protected against rust and corrosion, with a safety factor of 2:1 on horizontal pulls only. The Quick Link can be used in a variety of applications to connect a number of our accessories to each other. They provide low cost, ease of use and no maintenance.

Duct Puller O-Rings

Duct Puller O-Rings (90027)

 

Replacement O-Rings are available for all different series and sizes of DCD Duct Pullers.

DCD Design and Manufacturing

Place Your Order Now!