DCD Design offers a full range of duct installation and proofing equipment

Vibratory Plow Grip

Plow Grip (Series 00600)

This product is specifically designed for installation of PVC or PE duct by vibratory plow and is particularly suited to agricultural applications because of its quick installation and removal. DCD Plow-Grips are comprised of a stainless steel body and a clevis head with 8 links of hardened steel chain attached and hardened stainless steel expanding jaws with teeth that grip the inside of the ducting.

Pulling Eye Lug Style

Lug Style (00604)

The lug style is recommended when attaching directly to a line swivel or other clevis type connector.

Pulling Eye Clevis Style

Clevis Style (00605)

The clevis style pulling eyes are better if attaching to a pulling rope or wire with an eye that can be slotted into the clevis and simply attached with the pin provided.

Pulling Eye Swivel Clevis Style

Swivel Clevis Style (00620/00621)

This product is similar to the 00604 and 00605 series, but incorporates a built-in swivel head. These should only be used to install innerduct and are not suitable for use in any kind of directional drilling application.

Spiral Duct Brush

Spiral Duct Brush (08000)

In the 08000 Spiral Duct Brush, the flat steel bristles are spiraled onto heavy duty wire spindle with a pulling eye on one end only. This product will quickly remove grit or light dirt within the duct before installing your cable.

Heavy Duty Duct Brush

Heavy Duty Duct Brush (08100)

The 08100 Heavy Duty Wire Brushes are fitted with a pulling eye on each end so the brush could be pulled back and forth for those extra tough cleaning jobs. Following initial installation of the ducting, it is often a requirement that certain sized mandrels be pulled through the ducting to ensure that there has been no collapse or obstruction in the duct.

Steel Duct Checker

Steel Duct Checker (08400)

The 08400 Steel Duct Checker discs are tumbled to ensure no burrs and the spacers ensure easy bending around corners. The wire rope running through the mandrel is high quality, galvanized wire. Safety factor is 3:1.

Test Slug

Test Slug (08450)

These Test Slugs are simple aluminum mandrels designed to be pulled through the duct to test for out of roundness. The Slug diameters will fill approximately 70% of schedule 40 ducting and 80% of schedule 80 ducting. The ends are rounded for convenient pulling in either direction.

Polyurethane Duct Puller

Polyurethane Duct Checker

The 08500 Duct Checker discs are manufactured from high density polyurethane giving them the toughness to clear the duct without scraping or scratching the bore walls. The discs are spaced with gaps to allow passage through tight bends. The wire rope running through the mandrel is high quality, galvanized wire. Safety factor is 3:1.

Duct Puller

Duct Puller (00616)

This Duct Puller is nearly identical to the 00619 Series, except for the front face plate. The 00616 puller is made from zinc dichromate coated steel. This puller will also cover a larger range of bore sizes compared to the 00620 series and is made of fewer moving parts so maintenance and repair is easy.

For metric sizes, refer to the 00617 series.

Duct Puller

Duct Puller (00619)

This DCD puller has several features that make it a different puller than the others on the market. Most obvious is the polyurethane nose cone – this material has proved to be extremely durable during field testing. This puller will also cover a larger range of bore sizes compared to the 00620 series and is made of fewer moving parts so maintenance and repair is easy.

Duct Puller

Duct Puller (00620/00621)

These products are designed to grip polyethylene ducting using expanding jaws to grip the inside wall of the duct. This causes the pulling load to be spread around the circumference of the duct and allows a maximum load to be applied without damage to the ducting.

For metric sizes, refer to the 00621 series.

Duct Puller

Duct Puller (00650/00651)

These pullers have an outer sleeve that provides a complete seal around the ducting, preventing any fluids or contaminants from entering either the duct or the pulling eye. The pulling head is manufactured from alloy steel and is designed to protect the mechanism from heavy knocks or side loads. It is also fully sealed to prevent any fluid entry.

For metric sizes, refer to the 00651 series.

Pest Puller

Pest Puller (C2012-125)

The Pest Duct Puller is specifically sized for pulling HDPE steel armor conduit. The duct puller pulls, seals (tested to over 60 p.s.i.), and prevents the duct from stretching or the layers separating by utilizing the outer body in combination with the expanding jaws. It is designed for use with Dura-Line’s 1-1/4” Armor-Guard™ Conduit.

Duct Puller O-Rings

Duct Puller O-Rings (90027)

Replacement O-Rings are available for all different series and sizes of DCD Duct Pullers.
Place Your Order Now!

DCD Design and Manufacturing