Electrical Cable

Cable Pulling Eye Swivel Grip

Swivel-Grip (Series 00925)

The re-useable Swivel-Grip™ is used to install power cable and has a built-in swivel. The Swivel-Grip™ is constructed out of stainless steel with a radial bearing for bending load and a thrust bearing for tensile load. Grip is obtained by cutting away the cable jacket, feeding the core through the Cone nut and driving the tapered insert into the cable core. The higher the load, the further the insert is drawn into the tapered bore and the firmer the grip becomes. Note that this product is not designed to run around bullwheels.

Cable Pulling Eyes Power Grips Lug Style

Lug Style (24000)

The Lug Style are made out of Stainless Steel, with the exception of sizes 1250-2000 MCM, which are made out of carbon steel. These Power-Grips™ are much shorter than earlier models, which is better for going around corners or sheaves. They have also eliminated one body size so that now just 4 different bodies are used to pull up to 8 different cable sizes from 1/0 cable right up to 2000 MCM cable.

Cable Pulling Eye Power Grip Clevis Style

Clevis Style (24100)

This Pulling Eye has a clevis style head that will attach directly over the looped ends of the Bridle Slings, 23000 series, or other pulling attachments. This style of Power-Grip™ is made out of Stainless Steel, with the exception of sizes 1250-2000 MCM, which are made out of carbon steel. Only 4 body sizes are used to cover the range from 1/0 cable right up to 2000 MCM cable.

Multiplex Pushing Eye

Multiplex Pushing Eye (24200)

This product is designed to be threaded onto the lead end of a group of either Triplex or Quadplex cables so that they can be pushed through short lengths of ducting. The basic Pushing Eye comes with only the body and a shoulder bolt. There are several different attachments which can be threaded onto the bolt and these must be purchased separately.

Multiplex Pulling Eye

Multiplex Pulling Eye (24300)

This Stainless Steel product is designed to pull either Triplex or Quadplex cables. The 4-holes are sized for the cable conductors and each hole has three set screws to clamp down on the cable. Each product is also supplied with 3 spare set screws.

Cable Pulling Eye Mini Grip

Mini Grip (24500)

The Mini Grip Pulling Eye is re-usable and has a lug style head that will attach directly into a Line Swivel, 00505 series, or other type of connector. This Pulling Eye has 3 set screws that clamp directly onto the cable conductor. It is suitable for smaller cables with conductors having 7 strands or less.

Note: These Pulling Eyes should always be used with a Line Swivel (00505 series).

Pulling Harness

Pulling Harness (25000)

The purpose of the Pulling Harness is to allow single or multiple pulls at one time by attaching one or two cables to the one Pulling Harness. The Harness legs are manufactured from aircraft quality galvanized wire rope while the Connector end is manufactured from Stainless Steel. This product is available as a Single Harness or a Double Leg Harness.

Fiber Optic Cable

Mighty Eye Dielectric Strength Member

Dielectric Strength Member (00760)

Specially designed brass collets grip the central strength member and, if required, the kevlar yarn, while a tapered female thread grips the cable jacket. This way all parts of the cable are pulled simultaneously and the fibers get maximum protection.

 

Mighty Eye Steel Strength Member

Steel Strength Member (00770)

This re-useable stainless steel pulling eye is specifically designed for pulling Fiber Optic cable with a single, central, steel strength member. Specially designed so that three set screws can grip the steel strength member while a tapered female thread grips the cable jacket. This way all parts of the cable are pulled simultaneously and the fibers get maximum protection.

Cable Pulling Eyes Fiber Optic Combo Kit

Fiber Optic Combo Kit (00905)

These two kits allow various types of fiber optic cables to be pulled using different components. The main features of the kits include a pulling head with built-in swivel and breakaway body, a variety of breakaway pin sets, a variety of bodies for different cable diameters and a variety of collets for different strength member diameters. Both kits include solid pins when break load is not required. All components can be purchased individually for replacement parts. Custom kits can be built to specification.

Note: This product is not designed to run around bullwheels.

DCD Design and Manufacturing

Place Your Order Now!